- Gm tech 2 clone equivalent how to#
- Gm tech 2 clone equivalent serial#
- Gm tech 2 clone equivalent update#
- Gm tech 2 clone equivalent software#
Gm tech 2 clone equivalent software#
On the H2 the rear air ride is also one to be very careful of for doing software updates though.
Gm tech 2 clone equivalent update#
Those would run and make small adjustments a LOT more often than needed and the software update fixed that. One example in on the older single compressor air ride like 2003. I know just using that TIS2000 both GMC truck and 2003 H2 both had a bunch of software updates available to be programmed all of which fix small issues or improve certain aspects. There is a slightly more updated version of standalone TIS2000 floating around on the web which has additional updates that has software updates for vehicles through 2009 as well. Once you select programming on the Tech2 then go to the computer and you can immediately update each module right from the computer. In that method the process is the same but you leave the Tech2 connected to both the computer and the vehicle at the same time.
Gm tech 2 clone equivalent serial#
To use a long enough serial cable (its uses 9 pin serial adapters with an ethernet cable to make the cable longer – so you can just use a longer network cable) and do pass-through programming. The best, most reliable and safest method: It reads the Tech2 for the vehicle info and then presents you with a list of software for all of the modules and shows you which have updated software. You then connect it to the computer running TIS2000, GlobalTIS or TIS2WEB subscription and select programming in the computer. It interrogates all of the modules on the vehicle for the current versions and the VIN number. The way programming works is you connect the Tech2 to the vehicle and tell it you want to program a module. TIS2000 does have the actual programming for all vehicles up to 2007. The older TIS2000 software – that is what has the programming was discontinued in 2007. You only need those for doing actual programming. This is ONLY needed if you want to program or update the software in a module.ĪLL of the build in diagnostics and testing for vehicles up to 2013 works without the subscription or the older TIS2000 software. You can subscribe for as little as two days for $55. You should pay for an ACDelco TDS subscription for vehicles above 2007 and you would use the CANDI module that comes with many of the Tech2’s for working with CAN bus vehicles. I will need to get the tis2000 software loaded up for that.Īnd I have something good I’ve good when searching for TIS programming: I don’t see any reason why I won’t be able to program modules, etc. Overall, I am very impressed with the quality and capabilities. Well it pulls 3 codes, po455 (large evap leak), po442 (small evap leak), and po449 (vent solenoid control). The misfire codes shows me engine speed (rpm), ect, iat, spark, o2, maf, etc. For instance the c0050 shows me steering angle, speed, and a whole bunch of other things. The cool thing is that it records the event so you can see exactly what was happening at the time the code occurred. Also I did a check of all 28 modules in the car and pulled some misfire codes even no CEL was on. Hooked up the tech 2 and scanned the brake module for codes and I got c0050 for the right rear abs sensor. I suspected a wheel sensor but my blue tooth scanner wouldn’t pick it up. She has been having an issue with her abs light coming on then going off. Got a chance to try it out today on my wife’s Cadillac and my Hummer h3. The tis2000 needs to be installed on my laptop which will allow me to monitor pids, data log, etc Did some research on some other forums and a bunch of people have had really good luck with these clones.Ĭomes with 2 cds, the tis2000 software and instructions. I was looking into scanners and most can’t read anything but engine codes.
Gm tech 2 clone equivalent how to#
Now I just have to figure out how to use it properly lol. Took a few weeks to get it but it looks great so far.